Dometic RM2410 Uživatelský manuál stáhnout pdf (Strana 7)

- 7 -

ELECTRICAL CONNECTION

120 V AC CONNECTION

The refrigerator is equipped with a three-prong (grounding)

plug for your protection against shock hazards and should be

plugged directly into a properly grounded threeprong recep-

tacle. Do not cut or remove the grounding prong from this

plug.

The free length of the cord is 2 feet and

it is recommended that the receptacle is

located to the left of the refrigerator

(viewed from the rear) and approx. 6

inches from the oor. This allows easy

access through the vent door. The cord

should be routed to avoid direct contact

with the burner cover, ue cover or any

other components that could damage the

cord insulation.

12 V DC CONNECTION (RM2510)

12 V DC must be connected to the refrigerator to provide

power for operation of the automatic reigniter. The connection

is made to the terminal block marked 12 V, located on the back

of the refrigerator cabinet. Correct polarity must be observed

when connecting to the DC supply. The refrigerator must be

connected to the battery circuit with a maximum fuse size of 3

amps and a minimum wire size of 14 gauge.

NOTE!

Do not use the chassis or vehicle frame as one of the

conductors. Connect two wires at the refrigerator and route to

the DC supply.

120 Volt AC

receptacle

6”

INSTALLATION INSTRUCTIONS

TESTING LP GAS SAFETY SHUTOFF

The gas safety shutoff must be tested after the refrigerator is

connected to the LP gas supply.

RM2410

To test the gas safety shutoff, proceed as follows:

Turn on the refrigerator.

Check that the gas ame is lit. This can be observed

through the reector (E).

Close the gas valve by turning the knob (A) back to

the OFF position.

Wait one (1) minute.

Remove the protection cover.

Open the gas valve by turning the knob (A) to posi-

tion GAS without pushing the buttons (C) and (D).

Apply a non-corrosive commercial bubble solution

to the burner jet. Be careful not to damage the burner

jet.

No bubbles should appear at the opening of the

burner jet. Bubbles indicate a defective gas safety

shutoff and service is required.

If no bubbles were present at the burner jet, rinse the

orice with fresh water. Be careful not to damage the

burner jet orice.

Replace the protection cover.

Turn on the refrigerator. Normal gas operation

should return. Allow the burner to operate for a mini-

mum of 5 minutes.

RM2510

To test the gas safety shutoff, proceed as follows:

Turn on the refrigerator.

Check that the gas ame is lit and the lamp (E) is

out.

Close the gas valve by turning the knob (A) back to

the OFF position.

Wait one (1) minute.

Disconnect the 12 V DC power.

Remove the protection cover.

Open the gas valve by turning the knob (A) to posi-

tion GAS without pushing button (C). The reigniter

should not be sparking.

Apply a non-corrosive commercial bubble solution

to the burner jet. Be careful not to damage the burner

jet.

No bubbles should appear at the opening of the

burner jet. Bubbles indicate a defective gas safety

shutoff and service is required.

If no bubbles were present at the burner jet, rinse the

orice with fresh water. Be careful not to damage the

burner jet orice.

Replace the protection cover.

Reconnect the 12 V DC power to the refrigerator.

Turn on the refrigerator. Normal gas operation

should now return. Allow the burner to operate for a

minimum of 5 minutes.

10.

11.

10.

11.

12.

13.

1 2 3 4 5 6 7 8 9 10 11 12 ... 23 24

Komentáře k této Příručce

Žádné komentáře

Dometic RM2410 Uživatelský manuál Strana 7

Komentáře k této Příručce

Související produkty a manuály pro ne Dometic RM2410